This mini ramp is 3ft. Tall (from the ground to the top of the deck), 8ft. Vast and 24"-0 from end to finish (including each deck).As with all structures below on julianum.net, you can develop this mini ramp any size you want. However, for the product list to be accurate, friend will need to follow the plan as listed below.Keep in mind the this ramps dimensions were not liked at random. I invested weeks engineering a ramp that would certainly be cost and material efficient, funny to ride and most important, sturdy and safe.
You are watching: How much does it cost to build a mini ramp
whereby TO gain SUPPLIES
The wood and also hardware deserve to be found at most home advancement stores. Occasionally you can find the stole there as well, I understand my local residence Depot tote the coping and threshold material.If not, you can search the net for steel fabricators or salvage steel. Personally, I"ve begun buying my steel from MetalsDepot.com due to the fact that of their an extremely quick shipping and good prices. I"m no affiliated with them in any type of way, I just like them and their product.If this ramp is going to stay outside, it requirements to be safeguarded from the elements. A great place to begin is with push treated lumber, paint and a tarp. You might want come invest in a composite product for the surface too. Such as Skate Lite or Ramp Armor.Be extra mindful when working with treated wood though, the chemicals offered to act the hardwood contain a poisonous pesticide.
products needed 53 - 2x4"s, 8" long 4 - 4x8, 3/4" plywood 10 - 4x8, 3/8" plywood 5 - 4x8, 1/4" masonite 1 - 2 3/8" x 16" stole pipe 1 - 25lb Box, 1 5/8" screws 1 - 25lb Box, 2 1/2" screws 8 - clothesline bolts Tools required Tape measure up & PencilHammer and clampsCombination squareDrill w/ Drill BitsCircular & jig sawChalk LineFriend
Approximate Cost: $500Easy | | | | | an overwhelming
picking A location FOR your MINI RAMP
Ideally, a level driveway or concrete pad would certainly be the best spot for her mini ramp. But ramps often tend to gain pretty big and backyards and also fields become the only place big enough for them.If you"re placing your mini ramp top top terra firma (earth) you"ll have to make footings, or pads that the half pipe will sit on. You have the right to do this comparable to the method you develop a deck because that a house, through concrete blocks.I"ve created a separate page on ramp foundations, due to the fact that it"s an ext than can be spanned in a paragraph.
build IT
Below is a reduced list to express what you will need and it"s size.

shift LAYOUT diagram
Gather two sheets the 3/4" plywood because that the next templates. One sheet of 3/4" ply will carry out two sides.

through a jig saw, very carefully cut on the lines you attracted for the transition. When cut, you have the right to use this as your template to trace the 3 remaining transition sides.You"ll only require two 3/4" sides for each 8" ramp section. Most ramps room made in 4" sections yet this ramp is tiny enough to obtain away v an 8" span. Reduced the templates and collection them aside.
drawing THE transition
Take one 8" long 2x4 and on one end, drill a hole the diameter the a pencil (about 3/8"). Then measure up from the feet you just drilled, the size of the shift radius. In this case, 6"-0. Ar a screw there but don"t go all the way through the 2x4 yet.


frame THE change
Gather thirty four, 7"-10 1/2 long 2x4"s for the transition sections. Each 8" wide transition section calls for seventeen 2x4"s. This includes the deck part as well. Take 5 of those 7"-10 1/2 long 2x4"s and also start frame this ar by placing 2 2x4"s in ~ the back, one in ~ the front and also two top top the top beside the coping notch as displayed above.

including SUPPORTS
Place 2 2"-9 long 2x4"s under the deck 2x4"s where shown below. Use around eight, 1 5/8" screws to affix each one.These include extra assistance for the deck and also need come be inserted on every side in both change sections.

frame THE shift CONTINUED
Now affix twelve 7"-10 1/2 long 2x4"s, 8" on facility unless listed otherwise as shown below. Once this has been done, repeat the procedure for the 2nd transition section and set them aside because that now.The 2x4"s that space doubled in the lower section of the riding surface ar are necessary to produce a bigger surface area because that the seam of the first 3/8" plywood great to.

frame THE flat BOTTOM
Gather fifteen 7"-9 long 2x4"s because that the flat bottom supports. You"ll likewise need two, 8" long 2x4"s for the sides of the flat bottom section.Attach the 7"-9 long 2x4"s come the 8" long 2x4"s, 8" on center as shown below to complete the flat section.Pre drill the screw places at the end of the 2x4 through a 3/16" drill little to store the hardwood from splitting.Also, just like the transition, the 2x4"s need to be double where presented for the very first layer of 3/8" plywood.

put THE RAMP
Now that every one of the framing is done, the sections have the right to be attached to one another. Hope you have the ramps final location every squared far too. If no you have the right to learn an ext about ramp foundations here.Start by having a friend assist you relocate one transition section right into place. Then location the flat bottom section alongside the transition. Finally, place the last shift section alongside the level bottom section.

ASSEMBLING THE RAMP
If her mini ramp is on a concrete slab, you can attach the shift and flat bottom sections together using 2 1/2" screws. Screw them with each other from each side that the bottom with around six screws every side.


buying THE transaction

CUTTING and DRILLING THE transaction

attach THE transaction W/ SCREWS
when drilled, place the transaction in the notch ~ above the mini ramp. Revolve the pipeline so that the screws will certainly hit the 2x4 close come the center. Now location the screws in the holes and screw the pipe under snug.

connect THE coping W/ BOLTS

spanning THE DECKS
now that you have actually the coping every taken treatment of, it"s time to cover her ramp. Begin with the decks.Cut 2 sheets that 3/4" plywood under to 2"-9 wide. Connect a sheet to each deck section of the ramp with 1 5/8" screws. Room the screws about a foot except each other on the studs below.

on the 2nd layer, friend don"t want the plywood seams to be in the same place as the bottom layer. So reduced a paper of 3/8" plywood in fifty percent and connect it come the ramp the same method as the others.

covering THE RAMP
place a sheet of 3/8" plywood on the ramp. Push it flush versus the coping and begin attaching the ply with 1 5/8" screws. Start at the top and also work your method down, going from left to right favor reading a book. You might need who to aid you hold the ply in ar while you get the first couple of screws started.


See more: What Decimal Power Does The Abbreviation F Represent, Answered: Mass Ogam Temp
attaching THE final LAYER
begin with a full sheet that masonite and also press the flush against the coping similar to the an initial layer. Keep including sheets till you with the other side. As soon as again, cut the critical one come fit if necessary.The coping should stick out 3/8" indigenous riding surface. If it sticks out as well much, place wood shims under the masonite, near the transaction to raise the masonite. Shims are easily accessible at your neighborhood hardware store.

perfect 3FT MINI RAMP
Make sure you walk over the entire ramp before skating it. The last thing you want is to take a slide and there it is in a screw still sticking out.But if you"ve made the this far, you"re the proud owner the a brand new 3" mini ramp. Congratulations ~ above your brand-new mini ramp. Enjoy!

EMAILS I"VE RECIEVED native READERS...
Dave & Son"Just finished building the 3" mini ramp with my 13 year old son. We live in southern new Jersey.I want to tell you that your plans and instructions are spot on. I appreciate the moment you take it to put this out there for human being like us. It took about 3 full days to finish and also ended up costing united state $800. We used pressure treated wood and needed several bags of stone to level the area we wanted to placed it.What a great experience because that the 2 of us to execute this job together!-Dave"Thanks Dave, I evaluate the feedback. Glad the plans resolved for you and also your son.Thanks again, Jason
These men from Finland determined to placed a mini ramp in your office. I don"t check out why not, hahahaThanks guys, gain your ramp!